Edwards EST Fire Alarm Systems

Product Details:

Description. The Edwards EST SIGA-CT2 Dual Input Module is an intelligent analog addressable device used to connect one or two Class B normally-open Alarm, Supervisory, or Monitor type dry contact Initiating Device Circuits (IDC). For use exclusively with Edwards / EST's Signature Loop Controller.

Product Details:

The EST SIGI-271 is a fire alarm call point from Edwards' Signature Series system. It has the following features:
Break glass to activate
The switch is held off by the edge of the glass. When the glass is broken, the switch is released and an alarm is sent.
Protective coating
The glass has a plastic coating to prevent injury and stop glass fragments from being released.
Non-volatile memory
The call point stores the results of self-checks in its memory. This information includes the call point's serial number, address, and type code, as well as the date of manufacture, hours of operation, and more.
Alarm LED
A large red LED on the front of the call point indicates the alarm state. A flashing LED means the call point is in alarm, and a steady-on LED means the alarm state is in stand-alone mode.

Product Details:

The Edwards EST 270 is a fire alarm manual pull station that is part of the Signature Series system:
Appearance
The EST 270 has a teardrop shape and is made of die-cast zinc with a red epoxy powdercoat paint finish and aluminum colored stripes and markings.
Operation
The EST 270 is a single-action pull station that initiates an alarm when the user pulls the handle to break a glass rod.
Features
The EST 270 has an integral microprocessor, diagnostic LEDs, and is ADA compliant. It also has electronic addressing with non-volatile memory, automatic device mapping, and is designed for high ambient temperature operation.
Installation
The EST 270 can be mounted flush or on the surface. For flush mounting, a 4-inch standard North American square box with a single-gang plaster cover is required.
Compatibility
The EST 270 is compatible with the Signature Loop Controller. The loop controller electronically addresses each manual station, saving time during system commissioning.

Product Details:

The SIGA-CR is a control relay module that controls external appliances like fans, dampers, and door closers:
What it does
The SIGA-CR provides a Form C dry relay contact to control external appliances or equipment shutdown. It activates the normally open or normally-closed contact when commanded by the loop controller.
How it works
The SIGA-CR has an on-board microprocessor that ensures the relay is in the proper ON/OFF state. It requires one address on the signaling line circuit (SLC), and addresses are assigned electronically.
Where it can be mounted
The SIGA-CR can be mounted in a North American 2-1/2" (64 mm) deep 1-gang box, or standard 4" square 1-1/2" (38 mm) deep box with 1-gang cover.
Compatibility
The SIGA-CR is compatible only with GE Securitys Signature Loop Controller.
Versions
The SIGA-CR is available in two versions: Standard-mount versions and Plug-in UIO versions.

Product Details:

EDWARDS brand intelligent life safety systems offer the power
of high-end intelligent processing in configurations that deliver
uncomplicated solutions for small to mid-sized applications. With
intelligent detection, electronic addressing, automatic device
mapping, optional Ethernet connectivity, and a full line of easily-
configured option cards and modules, these flexible systems offer
versatility that benefits building owners and contractors alike.
The iO64 provides one Class B intelligent device loop that sup-
ports up to 64 device addresses, and two Class B Notification Ap-
pliance Circuits (NACs). Optional Class A device wiring is available
with the use of a module.
The iO1000 provides one Class A or Class B intelligent device
loop that supports up to 250 device addresses. Loop controller
modules may be added in combination to expand total system
capacity in 250-point increments to up to 1,000 device addresses.
The iO1000 panel includes four NACs that may be wired for either
Class A or Class B operation.
The RZI16-2 module adds even more capacity to iO installations
by adding up to 16 conventional device circuits and two additional
notification appliance circuits. This makes them an ideal retrofit
solution that can accommodate new intelligent detectors, as well
as existing conventional device

Product Details:

Edwards Est G1AVRF Wall Strobe features a sleek low profile design and energy-efficient technology that makes them less expensive to install and operate by reducing overhead. Also, high-performance LEDs require fewer circuits and power supplies.

Product Details:

The Signature Series SIGA-PHD(B) Intelligent Multisensor Photo-Heat Detector is an intelligent device that contains a photoelectric smoke sensor and a rate-of-rise heat sensor with a fixed temperature setting. The detector analyzes the data from both sensing devices and determines whether an alarm should be initiated.

Product Details:

The Edwards SIGA-CT1 Single Module is an intelligent analog addressable device that can use one or two Class B normally-open Alarm, Supervisory, or Monitor. In fact, the function of these modules is to personalize a code that will be selected by the installer.

Made In mexico.

Product Details:

The Edwards EST SIGA-OSHD is an intelligent multisensor smoke and heat detector that can detect a variety of fires, including smoldering and fast-flaming fires:
Smoke sensor: Uses an optical sensor to detect particles from combustion sources. It triggers an alarm when smoke density reaches a preprogrammed level.
Heat sensor: Uses a rate-of-rise sensor to detect fast-developing fires, and a fixed temperature threshold to detect fires.
Compatibility: Only works with control panels that use a Signature Loop controller.
Installation: Can be mounted to North American and European boxes.
Maintenance: Regular maintenance is required to ensure proper detector operation.
Smoke alarms are a critical part of home safety, as they can help detect fires early and potentially save lives.

Product Details:

The Edwards EST SIGA-PS is a photoelectric smoke detector that is part of the Signature Series Detection and Alarm equipment from Edwards / EST. It is designed to detect slow, smoldering fires. Here are some of its features:
Smoke sensing element: Gathers analog information and converts it into digital signals
Microprocessor: Measures and analyzes the signals, compares them to historical readings and time patterns, and makes an alarm decision
Digital filters: Remove signal patterns that are not typical of fires, virtually eliminating unwanted alarms
Compatibility: Only compatible with EST's Signature Loop Controller and uses one Device Address
Compatible bases and accessories: Includes the SIGA-SB Detector Mounting Base, the SIGA-SB4 4-inch Detector Mounting Base w/ SIGA-TS4 Trim Skirt, and the SIGA-RB Detector Mounting Base w/Relay
Weight and dimensions: Weighs 1 lb and is 5 × 5 × 5 in

Product Details:

The Edwards EST SIGA-PHS is a multisensor detector that combines a photoelectric smoke detector with a fixed-temperature heat detector. It uses a microprocessor to analyze information from the two fire sensors and compare it to historical readings, time patterns, and known fire characteristics to determine if an alarm should be triggered. The SIGA-PHS also uses digital filters to remove signal patterns that are not typical of fires.
Here are some more details about the SIGA-PHS:
It is only compatible with EST's Signature Loop Controller.
The manufacturer has discontinued the SIGA-PHS and replaced it with the SIGA-PHD.
Compatible bases and accessories include the SIGA-SB, SIGA-SB4, SIGA-RB, SIGA-IB, and SIGA-AB4.
Detectors can be addressed using the SIGA-PRO Signature Program/Service Tool.

Product Details:

Like all Signature Series detectors, the SIGA-COD is an intelligent device that gathers analog information from its CO sensor, converting this data into digital signals. To make an alarm decision, the detector's on-board microprocessor measures and analyzes sensor readings over time.

Product Details:

The Signature Optica Series SIGA-DS3I smoke detector
brings advanced optical sensing technology to a practical
design that increases efficiency, saves installation time,
cuts costs, and extends life safety and property protection
capabilities. Continuous self-diagnostics ensure reliability
over the long-haul, while environmental compensation helps
reduce maintenance costs.
Like all Signature Optica Series detectors, the SIGA-DS3I is an
intelligent device that gathers analog information from multiple
optical sensors, converting this data into digital signals. Utilizing
dual optical wavelengths combined with multiple detection angles,
the SIGA-DS3I differentiates particles that are not representative
of actual smoke. Particle data is input into digital filters which
feed a series of ratios removing signal patterns that are typical of
nuisance sources, thus reducing unwanted alarms. To make an
alarm decision, the detector’s on-board microprocessor measures
and analyzes all optical sensor readings and compares this
information to preprogrammed settings.

Product Details:

The Signature Optica Series SIGA-OSD smoke detector
brings advanced optical sensing technology to a practical
design that increases efficiency, saves installation time,
cuts costs, and extends life safety and property protection
capabilities. Continuous self-diagnostics ensure reliability
over the long-haul, while environmental compensation helps
reduce maintenance costs.
Like all Signature Optica Series detectors, the SIGA-OSD is an
intelligent device that gathers analog information from multiple
optical sensors, converting this data into digital signals. Utilizing
dual optical wavelengths combined with multiple detection angles,
the SIGA-OSD differentiates particles that are not representative
of actual smoke. Particle data is input into digital filters which
feed a series of ratios removing signal patterns that are typical of
nuisance sources, thus reducing unwanted alarms. To make an
alarm decision, the detector’s on-board microprocessor measures
and analyzes all optical sensor readings and compares this
information to preprogrammed settings.

Product Details:

The Edwards / EST (SIGA-CC1) Single Input Signal Module is a fire alarm module that connects circuits to power inputs. It's part of GE Security's Signature Series system and is an intelligent analog addressable device. Here are some of its features: 
 

Connections: Connects supervised Class B signals, audio speaker circuits, and telephone circuits to power inputs 
 

Power inputs: Power inputs can be 24 Vdc for audible and visible signal appliances, or 25 and 70 VRMS for audio evacuation speakers and firefighter's telephones 
 

Addressable: The SIGA-CC1 is an addressable module that receives an electronic address on the signaling line circuit 
 
Onboard microprocessor: Analyzes the signal and decides whether to input an alarm 
 
Short protection: The module won't activate if there's a short to prevent shorting the riser 
 
Fire to shut down: The module can shut down all electrical things in the event of a fire 
 
The SIGA-CC1 doesn't operate without electrical power, and it doesn't support conventional smoke detectors.

Product Details:

The SIGA-IM Isolator Module is an addressable device that protects a signaling line circuit (SLC) from a wire-to-wire short:
How it works
The SIGA-IM module monitors line voltages and opens the SLC when a short is detected. This isolates the short between the two isolator modules closest to the short.
Part of the Signature Series system
The SIGA-IM module is part of EST's Signature Series system. It can be wired into a Class A data loop at any point.
Features
The SIGA-IM module has a microprocessor that provides self-diagnostics, a history log, automatic device mapping, and fast, stable communication.
Installation
To install the module, you can write the module's address on the label provided, apply the label to the module, and attach the serial number label to the project documentation.

Product Details:

The Edwards EST 6830-3 is a Fire Alarm Telephone Handset for emergency use.